Adding OpenWrt support for Wi-Tek WI-R1 router

Model WI-R1 - FTTx Reverse PoE Router - Version:V16.12.23 R105
OpenWrt Chaos Calmer 15.05.1 r49404

> **SYSTEM LOG**
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    0.470000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi
> Fri Dec 23 10:42:08 2016 kern.warn kernel: [    0.480000] m25p80 spi32766.0: found s25fl064k, expected mx25l6405d
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.490000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.500000] 4 ofpart partitions found on MTD device spi32766.0
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.510000] Creating 4 MTD partitions on "spi32766.0":
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.520000] 0x000000000000-0x000000030000 : "u-boot"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.530000] 0x000000030000-0x000000040000 : "u-boot-env"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.540000] 0x000000040000-0x000000050000 : "factory"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.560000] 0x000000050000-0x000000800000 : "firmware"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.620000] 2 uimage-fw partitions found on MTD device firmware
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.640000] 0x000000050000-0x0000001676aa : "kernel"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.650000] 0x0000001676aa-0x000000800000 : "rootfs"
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.660000] mtd: device 5 (rootfs) set to be root filesystem
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.670000] 1 squashfs-split partitions found on MTD device rootfs
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    0.680000] 0x000000570000-0x000000800000 : "rootfs_data"
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.700000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.710000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.730000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.740000] rt2880_wdt 10000120.watchdog: Initialized
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.750000] TCP: cubic registered
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.760000] NET: Registered protocol family 17
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.770000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.790000] 8021q: 802.1Q VLAN Support v1.8
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.820000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    0.840000] Freeing unused kernel memory: 140K (8031d000 - 80340000)
> Fri Dec 23 10:42:08 2016 user.info kernel: [    3.250000] init: Console is alive
> Fri Dec 23 10:42:08 2016 user.info kernel: [    3.260000] init: - watchdog -
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.160000] usbcore: registered new interface driver usbfs
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.170000] usbcore: registered new interface driver hub
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.180000] usbcore: registered new device driver usb
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.220000] rt2880-pinmux pinctrl: request pin 17 (io17) for pio:17
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    7.230000] SCSI subsystem initialized
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.240000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.260000] ehci-platform: EHCI generic platform driver
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.280000] phy phy-usbphy.0: remote usb device wakeup disabled
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.290000] phy phy-usbphy.0: UTMI 16bit 30MHz
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.300000] ehci-platform 101c0000.ehci: EHCI Host Controller
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.310000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.330000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.360000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.370000] usb usb1: no of_node; not parsing pinctrl DT
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.370000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.370000] hub 1-0:1.0: USB hub found
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.380000] hub 1-0:1.0: 1 port detected
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.390000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.400000] ohci-platform: OHCI generic platform driver
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.410000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.420000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.440000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.510000] usb usb2: no of_node; not parsing pinctrl DT
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.510000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.510000] hub 2-0:1.0: USB hub found
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.520000] hub 2-0:1.0: 1 port detected
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.530000] rt2880-pinmux pinctrl: request pin 38 (io38) for pio:38
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.530000] rt2880-pinmux pinctrl: request pin 39 (io39) for pio:39
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [    7.530000] rt2880-pinmux pinctrl: request pin 72 (io72) for pio:72
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    7.530000] usbcore: registered new interface driver usb-storage
> Fri Dec 23 10:42:08 2016 user.info kernel: [    8.340000] init: - preinit -
> Fri Dec 23 10:42:08 2016 kern.info kernel: [    9.300000] 8021q: adding VLAN 0 to HW filter on device eth0
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [    9.360000] random: mktemp urandom read with 14 bits of entropy available
> Fri Dec 23 10:42:08 2016 user.info kernel: [   12.580000] mount_root: loading kmods from internal overlay
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [   13.880000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
> Fri Dec 23 10:42:08 2016 user.info kernel: [   13.910000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
> Fri Dec 23 10:42:08 2016 user.info kernel: [   13.940000] block: extroot: not configured
> Fri Dec 23 10:42:08 2016 kern.notice kernel: [   14.230000] jffs2: notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
> Fri Dec 23 10:42:08 2016 user.info kernel: [   15.140000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
> Fri Dec 23 10:42:08 2016 user.info kernel: [   15.160000] block: extroot: not configured
> Fri Dec 23 10:42:08 2016 user.info kernel: [   15.170000] mount_root: switching to jffs2 overlay
> Fri Dec 23 10:42:08 2016 user.info kernel: [   15.210000] procd: - early -
> Fri Dec 23 10:42:08 2016 user.info kernel: [   15.210000] procd: - watchdog -
> Fri Dec 23 10:42:08 2016 user.info kernel: [   16.150000] procd: - ubus -
> Fri Dec 23 10:42:08 2016 user.info kernel: [   17.170000] procd: - init -
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.300000] NET: Registered protocol family 10
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.320000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.340000] ip6_tables: (C) 2000-2006 Netfilter Core Team
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.390000] u32 classifier
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.390000]     input device check on
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.400000]     Actions configured
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.410000] Mirror/redirect action on
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.430000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.470000] fuse init (API version 7.23)
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.480000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.500000] Backport generated by backports.git backports-20151218-0-g2f58d9d
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.560000] usbcore: registered new interface driver ums-alauda
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.580000] usbcore: registered new interface driver ums-cypress
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.610000] usbcore: registered new interface driver ums-datafab
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.630000] usbcore: registered new interface driver ums-freecom
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.640000] usbcore: registered new interface driver ums-isd200
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.650000] usbcore: registered new interface driver ums-jumpshot
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.670000] usbcore: registered new interface driver ums-karma
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.680000] usbcore: registered new interface driver ums-sddr09
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.700000] usbcore: registered new interface driver ums-sddr55
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.710000] usbcore: registered new interface driver ums-usbat
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.760000] xt_time: kernel timezone is -0000
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.870000] PPP generic driver version 2.4.2
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.880000] NET: Registered protocol family 24
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.920000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
> Fri Dec 23 10:42:08 2016 kern.info kernel: [   18.940000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
> Fri Dec 23 10:42:08 2016 kern.debug kernel: [   18.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> Fri Dec 23 10:42:10 2016 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
> Fri Dec 23 10:42:11 2016 daemon.err block: /dev/mtdblock6 is already mounted
> Fri Dec 23 10:42:13 2016 authpriv.info dropbear[939]: Not backgrounding
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.300000] 8021q: adding VLAN 0 to HW filter on device eth0
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.330000] device eth0.1 entered promiscuous mode
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.340000] device eth0 entered promiscuous mode
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.360000] br-lan: port 1(eth0.1) entered forwarding state
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.370000] br-lan: port 1(eth0.1) entered forwarding state
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'lan' is enabled
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'lan' is setting up now
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'lan' is now up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'loopback' is enabled
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'loopback' is setting up now
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'loopback' is now up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan' is enabled
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan' is setting up now
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan6' is enabled
> Fri Dec 23 10:42:14 2016 kern.info kernel: [   27.480000] IPv6: ADDRCONF(NETDEV_UP): br-guest: link is not ready
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'guest' is enabled
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'guest' is setting up now
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'guest' is now up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Bridge 'br-lan' link is up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'lan' has link connectivity 
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Network device 'eth0' link is up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Network device 'lo' link is up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'loopback' has link connectivity 
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: VLAN 'eth0.2' link is up
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan' has link connectivity 
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan6' has link connectivity 
> Fri Dec 23 10:42:14 2016 daemon.notice netifd: Interface 'wan6' is setting up now
> Fri Dec 23 10:42:14 2016 daemon.err insmod: module is already loaded - xt_multiport
> Fri Dec 23 10:42:15 2016 daemon.notice netifd: wan (1088): udhcpc (v1.23.2) started
> Fri Dec 23 10:42:15 2016 daemon.err insmod: module is already loaded - xt_comment
> Fri Dec 23 10:42:15 2016 daemon.err insmod: module is already loaded - xt_length
> Fri Dec 23 10:42:15 2016 daemon.notice netifd: wan (1088): Sending discover...
> Fri Dec 23 10:42:15 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
> Fri Dec 23 10:42:16 2016 kern.info kernel: [   29.370000] br-lan: port 1(eth0.1) entered forwarding state
> Fri Dec 23 10:42:17 2016 daemon.err insmod: module is already loaded - xt_multiport
> Fri Dec 23 10:42:17 2016 daemon.err insmod: module is already loaded - xt_comment
> Fri Dec 23 10:42:17 2016 daemon.err insmod: module is already loaded - xt_length
> Fri Dec 23 10:42:17 2016 daemon.notice netifd: radio0 (1050): command failed: Operation not supported (-122)
> Fri Dec 23 10:42:18 2016 daemon.notice netifd: wan (1088): Sending discover...
> Fri Dec 23 10:42:19 2016 daemon.notice netifd: radio0 (1050): Configuration file: /var/run/hostapd-phy0.conf
> Fri Dec 23 10:42:19 2016 kern.info kernel: [   32.390000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> Fri Dec 23 10:42:19 2016 daemon.notice netifd: radio0 (1050): wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
> Fri Dec 23 10:42:19 2016 daemon.notice netifd: radio0 (1050): wlan0: interface state COUNTRY_UPDATE->HT_SCAN
> Fri Dec 23 10:42:19 2016 kern.info kernel: [   32.570000] device wlan0 entered promiscuous mode
> Fri Dec 23 10:42:20 2016 user.emerg syslog: setting up led USB
> Fri Dec 23 10:42:20 2016 user.emerg syslog: setting up led wifi
> Fri Dec 23 10:42:20 2016 daemon.info procd: - init complete -
> Fri Dec 23 10:42:21 2016 daemon.notice netifd: wan (1088): Sending discover...
> Fri Dec 23 10:42:21 2016 daemon.notice netifd: radio0 (1050): 20/40 MHz operation not permitted on channel pri=6 sec=10 based on overlapping BSSes
> Fri Dec 23 10:42:21 2016 daemon.notice netifd: radio0 (1050): Using interface wlan0 with hwaddr 18:8b:15:06:8a:6c and ssid "WI-TEK_068A6C"
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   34.980000] device wlan0-1 entered promiscuous mode
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   34.990000] br-guest: port 1(wlan0-1) entered forwarding state
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.000000] br-guest: port 1(wlan0-1) entered forwarding state
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.020000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: radio0 (1050): Using interface wlan0-1 with hwaddr 18:8b:15:06:8a:6d and ssid "WI-TEK_Guest"
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: radio0 (1050): wlan0: interface state HT_SCAN->ENABLED
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: radio0 (1050): wlan0: AP-ENABLED 
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.170000] br-lan: port 2(wlan0) entered forwarding state
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.180000] br-lan: port 2(wlan0) entered forwarding state
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.200000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.210000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
> Fri Dec 23 10:42:22 2016 kern.info kernel: [   35.220000] IPv6: ADDRCONF(NETDEV_CHANGE): br-guest: link becomes ready
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: Bridge 'br-guest' link is up
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: Interface 'guest' has link connectivity 
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: Network device 'wlan0' link is up
> Fri Dec 23 10:42:22 2016 daemon.notice netifd: Network device 'wlan0-1' link is up
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: started, version 2.73 cachesize 150
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: DNS service limited to local subnets
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq-dhcp[1470]: DHCP, IP range 10.0.0.100 -- 10.0.0.249, lease time 12h
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq-dhcp[1470]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: using local addresses only for domain lan
> Fri Dec 23 10:42:23 2016 daemon.warn dnsmasq[1470]: no servers found in /tmp/resolv.conf.auto, will retry
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: read /etc/hosts - 2 addresses
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq[1470]: read /tmp/hosts/dhcp - 1 addresses
> Fri Dec 23 10:42:23 2016 daemon.info dnsmasq-dhcp[1470]: read /etc/ethers - 0 addresses
> Fri Dec 23 10:42:24 2016 kern.info kernel: [   37.000000] br-guest: port 1(wlan0-1) entered forwarding state
> Fri Dec 23 10:42:24 2016 kern.info kernel: [   37.180000] br-lan: port 2(wlan0) entered forwarding state
> Fri Dec 23 10:42:24 2016 user.notice firewall: Reloading firewall due to ifup of guest (br-guest)
> Fri Dec 23 10:42:52 2016 kern.notice kernel: [   65.040000] random: nonblocking pool is initialized
> Fri Dec 23 11:06:08 2016 authpriv.info dropbear[1730]: Child connection from 192.168.1.66:6570
> Fri Dec 23 11:06:11 2016 authpriv.notice dropbear[1730]: Password auth succeeded for 'wayne' from 192.168.1.66:6570
> Fri Dec 23 11:06:13 2016 authpriv.info dropbear[1739]: Child connection from 192.168.1.66:6571
> Fri Dec 23 11:06:18 2016 authpriv.notice dropbear[1739]: Password auth succeeded for 'wayne' from 192.168.1.66:6571

Model WI-R1 - FTTx Reverse PoE Router - Version:V16.12.23 R105
OpenWrt Chaos Calmer 15.05.1 r49404

> **KERNEL LOG**
> [    0.000000] Linux version 3.18.36 (wayne@wayne-Ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49404) ) #105 Fri Dec 23 10:41:52 CST 2016
> [    0.000000] Board has DDR1
> [    0.000000] Analog PMU set to hw control
> [    0.000000] Digital PMU set to hw control
> [    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
> [    0.000000] bootconsole [early0] enabled
> [    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
> [    0.000000] MIPS: machine is WI-R1
> [    0.000000] Determined physical RAM map:
> [    0.000000]  memory: 04000000 @ 00000000 (usable)
> [    0.000000] Initrd not found or empty - disabling initrd
> [    0.000000] Zone ranges:
> [    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
> [    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
> [    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
> [    0.000000] On node 0 totalpages: 16384
> [    0.000000] free_area_init_node: node 0, pgdat 803040d0, node_mem_map 81000000
> [    0.000000]   Normal zone: 128 pages used for memmap
> [    0.000000]   Normal zone: 0 pages reserved
> [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
> [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [    0.000000] pcpu-alloc: [0] 0 
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
> [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
> [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
> [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> [    0.000000] Writing ErrCtl register=0006a087
> [    0.000000] Readback ErrCtl register=0006a087
> [    0.000000] Memory: 61372K/65536K available (2530K kernel code, 129K rwdata, 520K rodata, 140K init, 186K bss, 4164K reserved)
> [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [    0.000000] NR_IRQS:256
> [    0.000000] CPU Clock: 580MHz
> [    0.000000] systick: running - mult: 214748, shift: 32
> [    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
> [    0.070000] pid_max: default: 32768 minimum: 301
> [    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.090000] pinctrl core: initialized pinctrl subsystem
> [    0.100000] NET: Registered protocol family 16
> [    0.110000] rt2880-pinmux pinctrl: try to register 73 pins ...
> [    0.110000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux
> [    0.110000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux
> [    0.110000] pinctrl core: add 6 pinmux maps
> [    0.110000] rt2880-pinmux pinctrl: found group selector 12 for ephy
> [    0.110000] rt2880-pinmux pinctrl: found group selector 0 for i2c
> [    0.110000] rt2880-pinmux pinctrl: found group selector 1 for uartf
> [    0.110000] rt2880-pinmux pinctrl: found group selector 7 for spi refclk
> [    0.110000] rt2880-pinmux pinctrl: found group selector 11 for wled
> [    0.110000] rt2880-pinmux pinctrl: found group selector 4 for wdt
> [    0.110000] rt2880-pinmux pinctrl: request pin 40 (io40) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 41 (io41) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 42 (io42) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 43 (io43) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 44 (io44) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 37 (io37) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 38 (io38) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 39 (io39) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 72 (io72) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl
> [    0.110000] rt2880-pinmux pinctrl: failed to lookup the sleep state
> [    0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios
> [    0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
> [    0.140000] rt2880_gpio 10000638.gpio: registering 16 gpios
> [    0.150000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
> [    0.160000] rt2880_gpio 10000660.gpio: registering 32 gpios
> [    0.170000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
> [    0.180000] rt2880_gpio 10000688.gpio: registering 1 gpios
> [    0.190000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
> [    0.200000] Switched to clocksource systick
> [    0.210000] NET: Registered protocol family 2
> [    0.210000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.240000] TCP: Hash tables configured (established 1024 bind 1024)
> [    0.250000] TCP: reno registered
> [    0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [    0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [    0.280000] NET: Registered protocol family 1
> [    0.290000] PCI: CLS 0 bytes, default 32
> [    0.290000] rt-timer 10000100.timer: maximum frequency is 2441Hz
> [    0.310000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
> [    0.310000] futex hash table entries: 256 (order: -1, 3072 bytes)
> [    0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [    0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [    0.360000] msgmni has been set to 119
> [    0.380000] io scheduler noop registered
> [    0.380000] io scheduler deadline registered (default)
> [    0.390000] ralink-usb-phy usbphy: invalid resource
> [    0.400000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
> [    0.420000] serial8250 serial8250: no of_node; not parsing pinctrl DT
> [    0.420000] pinctrl core: add 1 pinmux maps
> [    0.420000] rt2880-pinmux pinctrl: found group selector 3 for uartlite
> [    0.420000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite
> [    0.420000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite
> [    0.420000] console [ttyS0] disabled
> [    0.420000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
> [    0.440000] console [ttyS0] enabled
> [    0.460000] bootconsole [early0] disabled
> [    0.470000] pinctrl core: add 1 pinmux maps
> [    0.470000] rt2880-pinmux pinctrl: found group selector 2 for spi
> [    0.470000] rt2880-pinmux pinctrl: request pin 3 (io3) for 10000b00.spi
> [    0.470000] rt2880-pinmux pinctrl: request pin 4 (io4) for 10000b00.spi
> [    0.470000] rt2880-pinmux pinctrl: request pin 5 (io5) for 10000b00.spi
> [    0.470000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi
> [    0.480000] m25p80 spi32766.0: found s25fl064k, expected mx25l6405d
> [    0.490000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
> [    0.500000] 4 ofpart partitions found on MTD device spi32766.0
> [    0.510000] Creating 4 MTD partitions on "spi32766.0":
> [    0.520000] 0x000000000000-0x000000030000 : "u-boot"
> [    0.530000] 0x000000030000-0x000000040000 : "u-boot-env"
> [    0.540000] 0x000000040000-0x000000050000 : "factory"
> [    0.560000] 0x000000050000-0x000000800000 : "firmware"
> [    0.620000] 2 uimage-fw partitions found on MTD device firmware
> [    0.640000] 0x000000050000-0x0000001676aa : "kernel"
> [    0.650000] 0x0000001676aa-0x000000800000 : "rootfs"
> [    0.660000] mtd: device 5 (rootfs) set to be root filesystem
> [    0.670000] 1 squashfs-split partitions found on MTD device rootfs
> [    0.680000] 0x000000570000-0x000000800000 : "rootfs_data"
> [    0.700000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
> [    0.710000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
> [    0.730000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
> [    0.740000] rt2880_wdt 10000120.watchdog: Initialized
> [    0.750000] TCP: cubic registered
> [    0.760000] NET: Registered protocol family 17
> [    0.770000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
> [    0.790000] 8021q: 802.1Q VLAN Support v1.8
> [    0.820000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
> [    0.840000] Freeing unused kernel memory: 140K (8031d000 - 80340000)
> [    3.250000] init: Console is alive
> [    3.260000] init: - watchdog -
> [    7.160000] usbcore: registered new interface driver usbfs
> [    7.170000] usbcore: registered new interface driver hub
> [    7.180000] usbcore: registered new device driver usb
> [    7.220000] rt2880-pinmux pinctrl: request pin 17 (io17) for pio:17
> [    7.230000] SCSI subsystem initialized
> [    7.240000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [    7.260000] ehci-platform: EHCI generic platform driver
> [    7.280000] phy phy-usbphy.0: remote usb device wakeup disabled
> [    7.290000] phy phy-usbphy.0: UTMI 16bit 30MHz
> [    7.300000] ehci-platform 101c0000.ehci: EHCI Host Controller
> [    7.310000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
> [    7.330000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
> [    7.360000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
> [    7.370000] usb usb1: no of_node; not parsing pinctrl DT
> [    7.370000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
> [    7.370000] hub 1-0:1.0: USB hub found
> [    7.380000] hub 1-0:1.0: 1 port detected
> [    7.390000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [    7.400000] ohci-platform: OHCI generic platform driver
> [    7.410000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
> [    7.420000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
> [    7.440000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
> [    7.510000] usb usb2: no of_node; not parsing pinctrl DT
> [    7.510000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
> [    7.510000] hub 2-0:1.0: USB hub found
> [    7.520000] hub 2-0:1.0: 1 port detected
> [    7.530000] rt2880-pinmux pinctrl: request pin 38 (io38) for pio:38
> [    7.530000] rt2880-pinmux pinctrl: request pin 39 (io39) for pio:39
> [    7.530000] rt2880-pinmux pinctrl: request pin 72 (io72) for pio:72
> [    7.530000] usbcore: registered new interface driver usb-storage
> [    8.340000] init: - preinit -
> [    9.300000] 8021q: adding VLAN 0 to HW filter on device eth0
> [    9.360000] random: mktemp urandom read with 14 bits of entropy available
> [   12.580000] mount_root: loading kmods from internal overlay
> [   13.880000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
> [   13.910000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
> [   13.940000] block: extroot: not configured
> [   14.230000] jffs2: notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
> [   15.140000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
> [   15.160000] block: extroot: not configured
> [   15.170000] mount_root: switching to jffs2 overlay
> [   15.210000] procd: - early -
> [   15.210000] procd: - watchdog -
> [   16.150000] procd: - ubus -
> [   17.170000] procd: - init -
> [   18.300000] NET: Registered protocol family 10
> [   18.320000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
> [   18.340000] ip6_tables: (C) 2000-2006 Netfilter Core Team
> [   18.390000] u32 classifier
> [   18.390000]     input device check on
> [   18.400000]     Actions configured
> [   18.410000] Mirror/redirect action on
> [   18.430000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
> [   18.470000] fuse init (API version 7.23)
> [   18.480000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
> [   18.500000] Backport generated by backports.git backports-20151218-0-g2f58d9d
> [   18.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
> [   18.560000] usbcore: registered new interface driver ums-alauda
> [   18.580000] usbcore: registered new interface driver ums-cypress
> [   18.610000] usbcore: registered new interface driver ums-datafab
> [   18.630000] usbcore: registered new interface driver ums-freecom
> [   18.640000] usbcore: registered new interface driver ums-isd200
> [   18.650000] usbcore: registered new interface driver ums-jumpshot
> [   18.670000] usbcore: registered new interface driver ums-karma
> [   18.680000] usbcore: registered new interface driver ums-sddr09
> [   18.700000] usbcore: registered new interface driver ums-sddr55
> [   18.710000] usbcore: registered new interface driver ums-usbat
> [   18.760000] xt_time: kernel timezone is -0000
> [   18.870000] PPP generic driver version 2.4.2
> [   18.880000] NET: Registered protocol family 24
> [   18.920000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
> [   18.940000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
> [   18.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> [   27.300000] 8021q: adding VLAN 0 to HW filter on device eth0
> [   27.330000] device eth0.1 entered promiscuous mode
> [   27.340000] device eth0 entered promiscuous mode
> [   27.360000] br-lan: port 1(eth0.1) entered forwarding state
> [   27.370000] br-lan: port 1(eth0.1) entered forwarding state
> [   27.480000] IPv6: ADDRCONF(NETDEV_UP): br-guest: link is not ready
> [   29.370000] br-lan: port 1(eth0.1) entered forwarding state
> [   32.390000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [   32.570000] device wlan0 entered promiscuous mode
> [   34.980000] device wlan0-1 entered promiscuous mode
> [   34.990000] br-guest: port 1(wlan0-1) entered forwarding state
> [   35.000000] br-guest: port 1(wlan0-1) entered forwarding state
> [   35.020000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
> [   35.170000] br-lan: port 2(wlan0) entered forwarding state
> [   35.180000] br-lan: port 2(wlan0) entered forwarding state
> [   35.200000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [   35.210000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
> [   35.220000] IPv6: ADDRCONF(NETDEV_CHANGE): br-guest: link becomes ready
> [   37.000000] br-guest: port 1(wlan0-1) entered forwarding state
> [   37.180000] br-lan: port 2(wlan0) entered forwarding state
> [   65.040000] random: nonblocking pool is initialized

@noodlenz Please use "Preformatted text </>" for logs, scripts, configs and general console output.
grafik

Please edit your postings accordingly.
Thanks!

1 Like

Please keep us posted how this goes! If you try the WRTNODE image, please let me know:

Thanks for the advise. I could not figure out how to do it.:grinning:

I used the OpenWrt install image for the WRTNODE, and the installation worked, though something wonky happened in the functionality. I will post again with more details.

Are there any diagnostic / test suites I can run on the device now that it's running OpenWrt 18.06.4? There seemed to be something malfunctioning with routing last week, but now in a new place I haven't yet recreated the error.

What doesn't work: I disable DHCP server for the lan interface (both IPv4 and IPv6), which should make the device function as a switch (this works on a TP-Link WDR3500 running OpenWrt), but it doesn't work.