Adding OpenWrt support for Juniper WLA532-WW

For Developers
1

Hi,

I have Juniper WLA532-WW AP. Can anybody upload openwrt firmware?

serial:

U-Boot 2009.11 (Aug 10 2012 - 09:43:51)

CPU:   P1011E, Version: 1.1, (0x80ed0011)
Core:  E500, Version: 5.1, (0x80212051)
Clock Configuration:
       CPU0:533.333 MHz,
       CCB:266.667 MHz,
       DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
       E500 Watchdog enabled
I2C:   ready
SPI:   ready
DRAM:  Configuring DDR for 666.667 MT/s data rate
Done Configuring DDR
DDR: 256 MB
...
FLASH: 32 MB
L2:    256 KB enabled
NAND:  0 MiB
    eTSEC2 is in sgmii mode.

    PCIE1 used as Root Complex (base addr ffe0a000)
Outbound memory range: c0000000:e0000000
PCICSRBAR @ 0xfff00000
R0 bus_start: 0 phys_start: 0 size: 10000000
PCI reg:0 00000000c0000000:00000000c0000000 0000000020000000 00000000
PCI reg:1 00000000ffc30000:0000000000000000 0000000000010000 00000001
PCI reg:2 00000000ffe00000:00000000fff00000 0000000000100000 00000100
PCI reg:3 0000000000000000:0000000000000000 0000000010000000 00000108
...PCIE LTSSM=0x16, Negotiated link width=1
               Scanning PCI bus 01
        01  00  168c  0000  0000  ff
    PCIE1 on bus 00 - 01

    PCIE2 used as Root Complex (base addr ffe09000)
Outbound memory range: a0000000:c0000000
PCICSRBAR @ 0xfff00000
R0 bus_start: 0 phys_start: 0 size: 10000000
PCI reg:0 00000000a0000000:00000000a0000000 0000000020000000 00000000
PCI reg:1 00000000ffc20000:0000000000000000 0000000000010000 00000001
PCI reg:2 00000000ffe00000:00000000fff00000 0000000000100000 00000100
PCI reg:3 0000000000000000:0000000000000000 0000000010000000 00000108
...PCIE LTSSM=0x16, Negotiated link width=1
               Scanning PCI bus 03
        03  00  168c  0000  0000  ff
    PCIE2 on bus 02 - 03

In:    serial
Out:   serial
Err:   serial
Net:   eTSEC2: PHY is Broadcom BCM54618SE (3625cd6)
eTSEC2

POST: Running .  .  .  . Model: WLA532
 .
POST: PASSED
U-Boot: Primary


Juniper Networks, Inc.
Version: 7.7.2.0.118


Autobooting in 3 seconds, press "q followed by <Enter>" to stop
## Starting application at 0x013FFFFC ...


    Juniper Networks AP Bootstrap 7.6.3 (11/xx/2011)


GO 1 entry_addr 00200000 ....

serial_io_init(): success!
1 Like
2

Yes, anybody can do that (some approval notwithstanding.) However, asking nicely for it does not make an OpenWrt version for your router appear.

That's a Freescale P1011 SoC, currently not a target in OpenWrt. Pretty sure noone is even working on that one.

3

Thank You takimata!

4

While there's no support for this paarticular model, the P1011 is part of the mpc85xx target. So the possibility is (depending on the WiFi module) there.

1 Like
5

Ah, that's interesting ... and not immediately obvious. I happily stand corrected.

1 Like
6

Hey nooy,

got my hands on one of those ap's . Would you like to share how you made this serial connect?

Thanks in advance

7

Hey.
Tell us how you connected Juniper WLA532-WW.
Thank.