Hello,
If I plugged in the stick:Pastebin.com Pastebin.com
andPastebin.com Pastebin.com
dsmesg plugging in and unplugging gives me this:
[57206.325361] usb 1-1.3: USB disconnect, device number 5
[57647.712673] usb 1-1.3: new high-speed USB device number 6 using ehci-platform
[57671.989335] usb 1-1.3: USB disconnect, device number 6
[57682.782681] usb 1-1.3: new high-speed USB device number 7 using ehci-platform
Thanks for you help
the iw output is useless, it's only the help screen.
post your installed packages.
have you installed mt7601u-firmware ?
root@GL-X750:~# lsusb
Bus 001 Device 004: ID 2c7c:0306 Quectel Wireless Solutions Co., Ltd. EG06/EP06/EM06 LTE-A modem
Bus 001 Device 003: ID 05e3:0752 Genesys Logic, Inc.
Bus 001 Device 007: ID 0e8d:7610 MediaTek Inc.
Bus 001 Device 002: ID 05e3:0618 Genesys Logic, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
And the installed packages:
root@GL-X750:~# opkg list-installed
ath10k-firmware-qca9887 - 2019-10-03-d622d160-1
base-files - 204.5-r11364-ef56c85848
blkid - 2.34-1
block-mount - 2020-05-12-84269037-1
bridge - 1.6-3
busybox - 1.30.1-6
ca-bundle - 20200601-1
ca-certificates - 20200601-1
cgi-io - 19
chat - 2.4.7.git-2019-05-25-3
comgt - 0.32-33
comgt-directip - 0.32-33
comgt-ncm - 0.32-33
curl - 7.66.0-3
ddns-scripts - 2.7.8-14
dnscrypt-proxy - 2018-11-22-f61ca76a-1
dnscrypt-proxy-resolvers - 2018-11-22-f61ca76a-1
dnsmasq-full - 2.80-16.3
dropbear - 2019.78-2
ebtables - 2018-06-27-48cff25d-1
ethtool - 5.2-1
fcgi - 2.4.2-1
firewall - 2019-11-22-8174814a-3
fstools - 2020-05-12-84269037-1
fwtool - 2
getdns - 1.6.0-5
getrandom - 2019-06-16-4df34a4d-4
gl-base-files - 3.0.539-1
gl-base-files-ar - 3.0.539-1
gl-bletool - 3.4.6
gl-cloud-ui - 3.0.36-1
gl-crond - 3.0.4-1
gl-ddns - 3.0.26-1
gl-firewall - 3.0.5-1
gl-fw - 3.0.29-1
gl-init-portal - 3.0.1-1
gl-ipv6 - 3.0.20-1
gl-modem - 3.0.162-1
gl-monitor - 3.0.133-1
gl-mqtt - 3.1.59-1
gl-portal - 3.0.27-1
gl-qos-internal - 3.0.38-1
gl-repeater - 3.1.19-1
gl-route-policy - 3.0.55-1
gl-rtty - 1.0.0-2
gl-s2s - 1.0.24-1
gl-sdk - 3.0.638-1
gl-siderouter - 3.0.0-1
gl-software - 3.0.30-1
gl-tertf - 4.0.45-1
gl-traffic - 1.0.5-1
gl-ui - 3.0.816-1
gl-upload - 1.0.46-1
gl-util - 3.0.223-1
gl-vpn - 3.0.129-1
gl-vpn-server - 3.0.129-1
gl-wan-detect - 3.0.1-1
gl-wg - 3.0.95-2
gl-wg-server - 3.0.95-2
gl-wifi-core - 3.0.222-1
hostapd-common - 2019-08-08-ca8c2bd2-7
ip-full - 5.0.0-2.1
ip6tables - 1.8.3-1
iperf3 - 3.7-1
ipset - 7.3-1
iptables - 1.8.3-1
iptables-mod-conntrack-extra - 1.8.3-1
iptables-mod-hashlimit - 1.8.3-1
iptables-mod-ipopt - 1.8.3-1
iptables-mod-u32 - 1.8.3-1
iw-full - 5.0.1-1
iwinfo - 2019-10-16-07315b6f-7
jshn - 2020-05-25-66195aee-1
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.241-1-05fa7e82a071f1ef387d47228067a82c
kmod-GobiNet - 4.14.241+3.0.0-1
kmod-GobiSerial - 4.14.241+3.0.0-1
kmod-ath - 4.14.241+4.19.193-1-1
kmod-ath10k - 4.14.241+4.19.193-1-1
kmod-ath9k - 4.14.241+4.19.193-1-1
kmod-ath9k-common - 4.14.241+4.19.193-1-1
kmod-cfg80211 - 4.14.241+4.19.193-1-1
kmod-crypto-aead - 4.14.241-1
kmod-crypto-crc32c - 4.14.241-1
kmod-crypto-ecb - 4.14.241-1
kmod-crypto-hash - 4.14.241-1
kmod-crypto-manager - 4.14.241-1
kmod-crypto-null - 4.14.241-1
kmod-crypto-pcompress - 4.14.241-1
kmod-crypto-sha1 - 4.14.241-1
kmod-ebtables - 4.14.241-1
kmod-fs-exfat - 4.14.241+2018-04-17-01c30ad5-2
kmod-fs-ext4 - 4.14.241-1
kmod-fs-ntfs - 4.14.241-1
kmod-fs-vfat - 4.14.241-1
kmod-fuse - 4.14.241-1
kmod-gpio-button-hotplug - 4.14.241-3
kmod-ip6tables - 4.14.241-1
kmod-ipt-compat-xtables - 4.14.241+2.14-9
kmod-ipt-conntrack - 4.14.241-1
kmod-ipt-conntrack-extra - 4.14.241-1
kmod-ipt-core - 4.14.241-1
kmod-ipt-hashlimit - 4.14.241-1
kmod-ipt-ipmark - 4.14.241+2.14-9
kmod-ipt-ipopt - 4.14.241-1
kmod-ipt-ipset - 4.14.241-1
kmod-ipt-nat - 4.14.241-1
kmod-ipt-nat6 - 4.14.241-1
kmod-ipt-offload - 4.14.241-1
kmod-ipt-raw - 4.14.241-1
kmod-ipt-u32 - 4.14.241-1
kmod-lib-crc-ccitt - 4.14.241-1
kmod-lib-crc16 - 4.14.241-1
kmod-lib-crc32c - 4.14.241-1
kmod-lib-textsearch - 4.14.241-1
kmod-mac80211 - 4.14.241+4.19.193-1-1
kmod-mii - 4.14.241-1
kmod-mppe - 4.14.241-1
kmod-mt7601u - 4.14.241+4.19.193-1-1
kmod-nf-conntrack - 4.14.241-1
kmod-nf-conntrack-netlink - 4.14.241-1
kmod-nf-conntrack6 - 4.14.241-1
kmod-nf-flow - 4.14.241-1
kmod-nf-ipt - 4.14.241-1
kmod-nf-ipt6 - 4.14.241-1
kmod-nf-nat - 4.14.241-1
kmod-nf-nat6 - 4.14.241-1
kmod-nf-nathelper - 4.14.241-1
kmod-nf-nathelper-extra - 4.14.241-1
kmod-nf-reject - 4.14.241-1
kmod-nf-reject6 - 4.14.241-1
kmod-nfnetlink - 4.14.241-1
kmod-nls-base - 4.14.241-1
kmod-nls-cp437 - 4.14.241-1
kmod-nls-iso8859-1 - 4.14.241-1
kmod-nls-utf8 - 4.14.241-1
kmod-phy-ath79-usb - 4.14.241-1
kmod-ppp - 4.14.241-1
kmod-pppoe - 4.14.241-1
kmod-pppox - 4.14.241-1
kmod-rt2800-lib - 4.14.241+4.19.193-1-1
kmod-rt2800-usb - 4.14.241+4.19.193-1-1
kmod-rt2x00-lib - 4.14.241+4.19.193-1-1
kmod-rt2x00-usb - 4.14.241+4.19.193-1-1
kmod-sched - 4.14.241-1
kmod-sched-connmark - 4.14.241-1
kmod-sched-core - 4.14.241-1
kmod-scsi-core - 4.14.241-1
kmod-slhc - 4.14.241-1
kmod-tun - 4.14.241-1
kmod-udptunnel4 - 4.14.241-1
kmod-udptunnel6 - 4.14.241-1
kmod-usb-acm - 4.14.241-1
kmod-usb-core - 4.14.241-1
kmod-usb-ehci - 4.14.241-1
kmod-usb-net - 4.14.241-1
kmod-usb-net-cdc-ether - 4.14.241-1
kmod-usb-net-cdc-ncm - 4.14.241-1
kmod-usb-net-huawei-cdc-ncm - 4.14.241-1
kmod-usb-net-ipheth - 4.14.241-1
kmod-usb-net-qmi-wwan - 4.14.241-1
kmod-usb-net-rndis - 4.14.241-1
kmod-usb-net-sierrawireless - 4.14.241-1
kmod-usb-ohci - 4.14.241-1
kmod-usb-serial - 4.14.241-1
kmod-usb-serial-cp210x - 4.14.241-1
kmod-usb-serial-option - 4.14.241-1
kmod-usb-serial-sierrawireless - 4.14.241-1
kmod-usb-serial-wwan - 4.14.241-1
kmod-usb-storage - 4.14.241-1
kmod-usb-storage-uas - 4.14.241-1
kmod-usb-uhci - 4.14.241-1
kmod-usb-wdm - 4.14.241-1
kmod-usb2 - 4.14.241-1
kmod-wireguard - 4.14.241+1.0.20200611-3
libblkid1 - 2.34-1
libblobmsg-json - 2020-05-25-66195aee-1
libc - 1.1.24-2
libcap - 2.27-1
libcurl4 - 7.66.0-3
libelf1 - 0.177-1
libev - 4.25-1
libgcc1 - 7.5.0-2
libgmp10 - 6.1.2-2
libimobiledevice - 1.3.0-2
libip4tc2 - 1.8.3-1
libip6tc2 - 1.8.3-1
libipset13 - 7.3-1
libiwinfo-lua - 2019-10-16-07315b6f-7
libiwinfo20181126 - 2019-10-16-07315b6f-7
libjson-c2 - 0.12.1-3.1
libjson-script - 2020-05-25-66195aee-1
liblua5.1.5 - 5.1.5-3
liblucihttp-lua - 2019-07-05-a34a17d5-1
liblucihttp0 - 2019-07-05-a34a17d5-1
libmnl0 - 1.0.4-2
libnetfilter-conntrack3 - 2018-05-01-3ccae9f5-2
libnettle7 - 3.5.1-1
libnfnetlink0 - 1.0.1-3
libnl-tiny - 0.1-5
libopenssl-conf - 1.1.1k-1
libopenssl1.1 - 1.1.1k-1
libpcap1 - 1.9.1-2.1
libpcre - 8.43-1
libplist - 2.2.0-2
libpthread - 1.1.24-2
librt - 1.1.24-2
libsodium - 1.0.18-1
libsqlite3-0 - 3310100-1
libubox20191228 - 2020-05-25-66195aee-1
libubus-lua - 2021-07-01-38c7fdd8-1
libubus20210603 - 2021-07-01-38c7fdd8-1
libuci20130104 - 2019-09-01-415f9e48-4
libuclient20160123 - 2020-06-17-51e16ebf-1
libusb-1.0-0 - 1.0.22-2
libusbmuxd - 2.0.2-1
libustream-openssl20150806 - 2020-03-13-40b563b1-1
libuuid1 - 2.34-1
libxml2 - 2.9.9-3
libxtables12 - 1.8.3-1
libyaml - 0.2.2-1
lighttpd - 1.4.48-2
lighttpd-mod-access - 1.4.48-2
lighttpd-mod-cgi - 1.4.48-2
lighttpd-mod-expire - 1.4.48-2
lighttpd-mod-fastcgi - 1.4.48-2
lighttpd-mod-proxy - 1.4.48-2
lighttpd-mod-redirect - 1.4.48-2
logd - 2019-06-16-4df34a4d-4
lua - 5.1.5-3
luci - git-21.189.23240-7b931da-1
luci-app-firewall - git-21.189.23240-7b931da-1
luci-app-opkg - git-21.189.23240-7b931da-1
luci-app-wireguard - git-21.189.23240-7b931da-1
luci-base - git-21.189.23240-7b931da-1
luci-i18n-wireguard-de - git-21.189.23240-7b931da-1
luci-lib-ip - git-21.189.23240-7b931da-1
luci-lib-json - git-21.189.23240-7b931da-1
luci-lib-jsonc - git-21.189.23240-7b931da-1
luci-lib-nixio - git-21.189.23240-7b931da-1
luci-mod-admin-full - git-21.189.23240-7b931da-1
luci-mod-network - git-21.189.23240-7b931da-1
luci-mod-rpc - git-21.189.23240-7b931da-1
luci-mod-status - git-21.189.23240-7b931da-1
luci-mod-system - git-21.189.23240-7b931da-1
luci-proto-3g - git-21.189.23240-7b931da-1
luci-proto-ipv6 - git-21.189.23240-7b931da-1
luci-proto-ncm - git-21.189.23240-7b931da-1
luci-proto-ppp - git-21.189.23240-7b931da-1
luci-proto-qmi - git-21.189.23240-7b931da-1
luci-proto-relay - git-21.189.23240-7b931da-1
luci-proto-wireguard - git-21.189.23240-7b931da-1
luci-theme-bootstrap - git-21.189.23240-7b931da-1
mqtt - 1.3.1-1
mt7601u-firmware - 20190416-1
mtd - 24
mwan3 - 2.8.4-2
netifd - 2021-01-09-753c351b-2
nodogsplash - 1.0.2-3
ntfs-3g - 2017.3.23-2-fuseint
odhcp6c - 2021-01-09-64e1b4e7-16
odhcpd-ipv6only - 2020-05-03-49e4949c-3
openssl-util - 1.1.1k-1
openvpn-openssl - 2.5.2-1
openwrt-keyring - 2021-02-20-49283916-2
opkg - 2021-01-31-c5dccea9-1
ppp - 2.4.7.git-2019-05-25-3
ppp-mod-pppoe - 2.4.7.git-2019-05-25-3
procd - 2020-03-07-09b9bd82-1
relayd - 2020-04-25-f4d759be-1
resolveip - 2
rpcd - 2020-05-26-67c8a3fd-1
rpcd-mod-file - 2020-05-26-67c8a3fd-1
rpcd-mod-iwinfo - 2020-05-26-67c8a3fd-1
rpcd-mod-luci - 20201107
rpcd-mod-rrdns - 20170710
rt2800-usb-firmware - 20190416-1
rtty-openssl - 8.0.0-2
smstools3 - 3.1.21-2
ssmtp - 2.64-7
stubby - 0.3.0-1
swconfig - 12
tc - 5.0.0-2.1
tcpdump - 4.9.3-2
ubi-utils - 2.1.1-1
uboot-envtools - 2021.01-10
ubox - 2019-06-16-4df34a4d-4
ubus - 2021-07-01-38c7fdd8-1
ubusd - 2021-07-01-38c7fdd8-1
uci - 2019-09-01-415f9e48-4
uclient-fetch - 2020-06-17-51e16ebf-1
uhttpd - 2020-10-01-3abcc891-1
unzip - 6.0-8
uqmi - 2019-06-27-1965c713-7
urandom-seed - 1.0-1
urngd - 2020-01-21-c7f7b6b6-1
usb-modeswitch - 2017-12-19-f40f84c2-2
usbmuxd - 1.1.1-1
usbutils - 007-10
usign - 2020-05-23-f1f65026-1
wireguard - 1.0.20200611-3
wireguard-tools - 1.0.20191226-1
wireless-regdb - 2020.11.20-1
wpa-cli - 2019-08-08-ca8c2bd2-7
wpad-openssl - 2019-08-08-ca8c2bd2-7
wwan - 2014-07-17-1
zlib - 1.2.11-3
and yes the bin-files is in the correct spot:
root@GL-X750:/lib/firmware/mediatek# ls
mt7610u.bin
have you rebooted your device, with the Alfa connected ?
yes, no idea if/where something would change
AFAIK, if the wifi stick is discovered during boot, it should add a new entry in the wireless section.
no new entry at wireless
here iw list:
root@GL-X750:~# iw list
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (23.0 dBm)
* 2417 MHz [2] (23.0 dBm)
* 2422 MHz [3] (23.0 dBm)
* 2427 MHz [4] (23.0 dBm)
* 2432 MHz [5] (23.0 dBm)
* 2437 MHz [6] (23.0 dBm)
* 2442 MHz [7] (23.0 dBm)
* 2447 MHz [8] (23.0 dBm)
* 2452 MHz [9] (23.0 dBm)
* 2457 MHz [10] (23.0 dBm)
* 2462 MHz [11] (23.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* testmode
* connect
* disconnect
* channel_switch
* set_qos_map
* set_multicast_to_unicast
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
P2P GO supports CT window setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports active monitor (which will ACK incoming frames)
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports configuring vdev MAC-addr on create.
Supported extended features:
* [ RRM ]: RRM
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
Wiphy phy0
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x1 RX 0x1
Configured Antennas: TX 0x1 RX 0x1
Supported interface modes:
* managed
* AP
* monitor
* mesh point
Band 2:
Capabilities: 0x196f
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-7
VHT Capabilities (0x33800132):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: not supported
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: not supported
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (radar detection)
* 5280 MHz [56] (23.0 dBm) (radar detection)
* 5300 MHz [60] (23.0 dBm) (radar detection)
* 5320 MHz [64] (23.0 dBm) (radar detection)
* 5500 MHz [100] (23.0 dBm) (radar detection)
* 5520 MHz [104] (23.0 dBm) (radar detection)
* 5540 MHz [108] (23.0 dBm) (radar detection)
* 5560 MHz [112] (23.0 dBm) (radar detection)
* 5580 MHz [116] (23.0 dBm) (radar detection)
* 5600 MHz [120] (23.0 dBm) (radar detection)
* 5620 MHz [124] (23.0 dBm) (radar detection)
* 5640 MHz [128] (23.0 dBm) (radar detection)
* 5660 MHz [132] (23.0 dBm) (radar detection)
* 5680 MHz [136] (23.0 dBm) (radar detection)
* 5700 MHz [140] (23.0 dBm) (radar detection)
* 5720 MHz [144] (23.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* testmode
* connect
* disconnect
* channel_switch
* set_qos_map
* set_multicast_to_unicast
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* monitor
valid interface combinations:
* #{ AP, mesh point } <= 8, #{ managed } <= 1,
total <= 8, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports static SMPS
Device supports configuring vdev MAC-addr on create.
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
it appears to be there, unless you have other radios attached in your device ?
it is a GL-x750v2, with built in LTE and 2 Wifi (2.4 Ghz and 5 Ghz)
are you sure you are running openwrt?
4 Likes
Surfer2010:
GL-x750v2
... and not gl.inet's "openwrt" ?
I'm running gl.inet's "openwrt", because running original openwrt I had a lot of trouble and failing at the end to get the lte modem to work with roaming, so i tried with gl-inet openwrt
then your thread should be at gl.inets forum ...
good spotting @Borromini
what is so different that this won't work on their version
dunno, ask them ...
that's bad, because using orignal openwrt i did first and did not get the lte modem to work properly :-/ so now i am stuck inbetween
try to install kmod-mt76x0u
opkg update
opkg install kmod-mt76x0u
1 Like
anon4457646:
kmod-mt76x0u
the GL-Admin panel looks like this (no additional wifi device)
