I tried the serial flashing instruction from the EC330-G5U page. It seems to have worked at first glance. Big problem I see so far is that the maximum transmit power for the wireless is limited to 6dbm. So, while the wireless does seem to work, you have to basically stand next to it to be in range.
Anyone have any ideas how to increase? Will keep doing research.
Below is the serial out from OpenWrt boot.
U-Boot 1.1.3 (Nov 13 2018 - 17:12:53)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87f9c000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 87fcacf0
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device found in MTK table, ID: c8d1, EXT_ID: 809540
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
partable is:
part0:0x20000@0x0
part1:0x7f60000@0x20000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Nov 13 2018 Time:17:12:53
============================================
THIS IS First Uboot: The first uboot located in NAND Flash to load next full-fea ture Uboot.
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
Press '1' or 't' to break the booting process 0
3: System Boot system code via Flash.
## Booting image at bc020000 ...
Image Name: NAND Flash I
Image Type: MIPS Linux Standalone Program (uncompressed)
Data Size: 183320 Bytes = 179 kB
Load Address: a01fc040
Entry Point: a0200000
... Verifying Checksum ... OK
data copied to 0xa01fc040
OK
jump to memory 0xa0200000
U-Boot 1.1.3 (Nov 13 2018 - 17:13:43)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87f88000
Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 87fc8f10
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 40]
Device found in MTK table, ID: c8d1, EXT_ID: 809540
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
.
partable is:
part0:0x400000@0x0
part1:0x7000000@0x400000
part2:0xb80000@0x7400000
.============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Nov 13 2018 Time:17:13:43
============================================
THIS IS Main Uboot: Including recovery webserver.
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
this uboot is loaded from 0xbc020000
Press '4' or 't' to break the booting process
Press 'x' to enter recovery web server 0
3: System Boot system code via Flash.
do_bootm
## Booting image at bc400000 ...
Image Name: OS IMAGE (OpenWrt)
Image Type: MIPS Linux Firmware (uncompressed)
Data Size: 2804668 Bytes = 2.7 MB
Load Address: 80001000
Entry Point: 80001000
ret is -3
try next header
## Booting image at bc400040 ...
Image Name: MIPS OpenWrt Linux-5.15.150
Image Type: MIPS Linux Standalone Program (uncompressed)
Data Size: 2804604 Bytes = 2.7 MB
Load Address: 80001000
Entry Point: 80001000
........................................... Verifying Checksum ... OK
data copied to 0x80001000
OK
jump to memory 0x80001000
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 5.15.150 (builder@buildhost) (mipsel-openwrt-linux- musl-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2. 40.0) #0 SMP Fri Mar 22 22:09:42 2024
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TP-Link EC330-G5u v1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17808 r8192 d23152 u49152
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jff s2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, li near)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, line ar)
[ 0.000000] Writing ErrCtl register=00010990
[ 0.000000] Readback ErrCtl register=00010990
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119272K/131072K available (7303K kernel code, 629K rwdata , 880K rodata, 1224K init, 225K bss, 11800K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478ab b4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 43980 46511103ns
[ 0.008061] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066216] pid_max: default: 32768 minimum: 301
[ 0.071630] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linea r)
[ 0.078844] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090432] rcu: Hierarchical SRCU implementation.
[ 0.095901] smp: Bringing up secondary CPUs ...
[ 0.101297] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101325] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.101340] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101383] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160677] Synchronize counters for CPU 1: done.
[ 0.193223] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.193246] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.193257] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.193284] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.252186] Synchronize counters for CPU 2: done.
[ 0.282838] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282860] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.282871] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282902] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.337376] Synchronize counters for CPU 3: done.
[ 0.367237] smp: Brought up 1 node, 4 CPUs
[ 0.377058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.386875] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.393958] pinctrl core: initialized pinctrl subsystem
[ 0.400808] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.407433] thermal_sys: Registered thermal governor 'step_wise'
[ 0.432712] clocksource: Switched to clocksource GIC
[ 0.439091] NET: Registered PF_INET protocol family
[ 0.444226] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear )
[ 0.452255] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.460569] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.468256] TCP established hash table entries: 1024 (order: 0, 4096 bytes, l inear)
[ 0.475883] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.482899] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.489341] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.495857] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.503195] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.508810] PCI: CLS 0 bytes, default 32
[ 0.515525] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.527344] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.533220] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.544481] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51)
[ 0.556076] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.561934] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.567937] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.574048] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.580723] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000 , using [bus 00-ff]
[ 0.589489] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.597605] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.962715] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 0.969611] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 0.974490] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.979306] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 0.986526] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 0.992830] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.998244] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.005101] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.011253] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.017204] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.023427] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[ 1.029674] pci 0000:00:00.0: supports D1
[ 1.033608] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.040214] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.046239] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.052415] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[ 1.058729] pci 0000:00:01.0: supports D1
[ 1.062647] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.070727] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 1.076749] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.083649] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.100038] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.105243] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.111242] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.118010] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref ]
[ 1.125179] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.132041] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[ 1.138036] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.144934] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.161322] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.166541] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.172541] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.179312] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref ]
[ 1.186482] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.193105] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.199620] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.206575] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.213126] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.220014] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.226790] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref ]
[ 1.233952] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.240662] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref ]
[ 1.247866] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 1.254607] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 1.261313] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.267401] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.273443] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bi t]
[ 1.280676] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.285622] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.291638] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.298405] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref ]
[ 1.305586] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bi t]
[ 1.312848] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.317730] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.323819] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.330517] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref ]
[ 1.340327] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.351449] printk: console [ttyS0] disabled
[ 1.355811] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.364829] printk: console [ttyS0] enabled
[ 1.364829] printk: console [ttyS0] enabled
[ 1.373096] printk: bootconsole [early0] disabled
[ 1.373096] printk: bootconsole [early0] disabled
[ 1.385945] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 1.392344] nand: ESMT NAND 128MiB 3,3V 8-bit
[ 1.396739] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64
[ 1.404313] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 1.410922] 7 fixed-partitions partitions found on MTD device mt7621-nand
[ 1.419180] Creating 7 MTD partitions on "mt7621-nand":
[ 1.424494] 0x000000000000-0x000000400000 : "u-boot"
[ 1.492164] 3 fixed-partitions partitions found on MTD device u-boot
[ 1.498559] Creating 3 MTD partitions on "u-boot":
[ 1.503357] 0x000000000000-0x000000020000 : "u-boot-first"
[ 1.511774] 0x000000020000-0x000000060000 : "u-boot-main"
[ 1.522087] 0x000000060000-0x0000000a0000 : "u-boot-main-reserve"
[ 1.533227] 0x000000400000-0x000003400000 : "os0"
[ 2.275808] 2 fixed-partitions partitions found on MTD device os0
[ 2.281916] Creating 2 MTD partitions on "os0":
[ 2.286485] 0x000000000000-0x000000400000 : "kernel"
[ 2.354333] 0x000000400000-0x000003000000 : "ubi-os0"
[ 3.035373] 0x000003400000-0x000006400000 : "os1"
[ 3.777768] 0x000006400000-0x000007400000 : "userfs"
[ 4.029272] 0x000007400000-0x000007800000 : "u-boot-env"
[ 4.097260] 0x000007800000-0x000007c00000 : "factory"
[ 4.164928] 0x000000000000-0x000007f80000 : "wholeflash"
[ 6.135185] Concatenating MTD devices:
[ 6.138989] (0): "ubi-os0"
[ 6.141699] (1): "userfs"
[ 6.144343] into device "ubi-concat"
[ 6.148013] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 6.154711] Creating 1 MTD partitions on "ubi-concat":
[ 6.159840] 0x000000000000-0x000003c00000 : "ubi"
[ 7.214763] mtk_soc_eth 1e100000.ethernet: generated random MAC address aa:ac :9c:90:88:a2
[ 7.223171] mtk_soc_eth 1e100000.ethernet: generated random MAC address 8a:61 :9e:30:66:09
[ 7.232734] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 7.246514] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe 100000, irq 21
[ 7.258572] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe1 00000, irq 21
[ 7.268854] i2c_dev: i2c /dev entries driver
[ 7.276423] NET: Registered PF_INET6 protocol family
[ 7.284120] Segment Routing with IPv6
[ 7.287861] In-situ OAM (IOAM) with IPv6
[ 7.291860] NET: Registered PF_PACKET protocol family
[ 7.297030] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 7.310620] 8021q: 802.1Q VLAN Support v1.8
[ 7.321270] gpio-export gpio-export: 1 gpio(s) exported
[ 7.327056] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 7.352643] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 7.360508] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control r x/tx
[ 7.364043] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] d river [MediaTek MT7530 PHY] (irq=24)
[ 7.381092] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] d river [MediaTek MT7530 PHY] (irq=25)
[ 7.393975] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] d river [MediaTek MT7530 PHY] (irq=26)
[ 7.406897] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] d river [MediaTek MT7530 PHY] (irq=27)
[ 7.419153] DSA: tree 0 setup
[ 7.426149] UBI: auto-attach mtd12
[ 7.429586] ubi0: attaching mtd12
[ 8.969670] ubi0: scanning is finished
[ 8.990449] ubi0: attached mtd12 (name "ubi", size 60 MiB)
[ 8.996028] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 9.002913] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 9.009676] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 9.016645] ubi0: good PEBs: 480, bad PEBs: 0, corrupted PEBs: 0
[ 9.022640] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 12 8
[ 9.029865] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequ ence number: 268961471
[ 9.038904] ubi0: available PEBs: 0, total reserved PEBs: 480, PEBs reserved for bad PEB handling: 10
[ 9.048149] ubi0: background thread "ubi_bgt0d" started, PID 354
[ 9.050883] block ubiblock0_0: created from ubi0:0(rootfs)
[ 9.059747] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 9.075748] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 9.086928] Freeing unused kernel image (initmem) memory: 1224K
[ 9.092918] This architecture does not have kernel memory protection.
[ 9.099348] Run /sbin/init as init process
[ 9.554834] init: Console is alive
[ 9.558644] init: - watchdog -
[ 10.367436] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 10.426950] usbcore: registered new interface driver usbfs
[ 10.432599] usbcore: registered new interface driver hub
[ 10.438208] usbcore: registered new device driver usb
[ 10.454674] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regula tor
[ 10.462371] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regu lator
[ 10.470275] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 10.475663] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus numb er 1
[ 10.488170] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 qu irks 0x0000000000290010
[ 10.497440] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 10.503455] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 10.508773] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus numb er 2
[ 10.516284] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 10.523737] hub 1-0:1.0: USB hub found
[ 10.527660] hub 1-0:1.0: 2 ports detected
[ 10.532744] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 10.541907] hub 2-0:1.0: USB hub found
[ 10.545883] hub 2-0:1.0: 1 port detected
[ 10.558772] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 10.571816] init: - preinit -
[ 11.411440] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.531683] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.584297] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.934947] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii l ink mode
[ 11.947494] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flo w control rx/tx
[ 11.953221] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 11.963515] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 14.136952] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 14.143041] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 506
[ 14.226031] UBIFS (ubi0:1): recovery needed
[ 14.348096] UBIFS (ubi0:1): recovery completed
[ 14.352812] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "root fs_data"
[ 14.360622] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 14.370517] UBIFS (ubi0:1): FS size: 53583872 bytes (51 MiB, 422 LEBs), max 4 32 LEBs, journal size 2666496 bytes (2 MiB, 21 LEBs)
[ 14.382154] UBIFS (ubi0:1): reserved for root: 2530898 bytes (2471 KiB)
[ 14.388761] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID F6FEE C9F-28DD-419F-8F8E-F71B71BA23C6, small LPT model
...