I have a Comfast CF-EW72 V2 router
The initial firmware was successful.
On 23.05.2 updated successfully, but the SSID of the 5GHz radio periodically goes into the off state.
After a reboot everything seems to be ok, but after the next reboot it turns off again.
Rebooting with an error takes a very long time: 4-5 minutes
Kernel log with error:
Summary
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is COMFAST CF-EW72 V2
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14736 r8192 d22128 u45056
[ 0.000000] pcpu-alloc: s14736 r8192 d22128 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00018080
[ 0.000000] Readback ErrCtl register=00018080
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119300K/131072K available (7300K kernel code, 624K rwdata, 880K rodata, 1232K init, 226K bss, 11772K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008038] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066210] pid_max: default: 32768 minimum: 301
[ 0.071600] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.078812] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090234] rcu: Hierarchical SRCU implementation.
[ 0.095668] smp: Bringing up secondary CPUs ...
[ 0.101031] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101055] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.101069] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101112] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160404] Synchronize counters for CPU 1: done.
[ 0.192449] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.192471] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.192482] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.192508] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.251627] Synchronize counters for CPU 2: done.
[ 0.282264] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282287] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.282298] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282329] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.336813] Synchronize counters for CPU 3: done.
[ 0.366664] smp: Brought up 1 node, 4 CPUs
[ 0.375678] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.385476] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.392546] pinctrl core: initialized pinctrl subsystem
[ 0.399351] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.405975] thermal_sys: Registered thermal governor 'step_wise'
[ 0.408649] rt2880-pinmux pinctrl: there is not valid maps for state default
[ 0.424825] FPU Affinity set after 11720 emulations
[ 0.437560] clocksource: Switched to clocksource GIC
[ 0.443892] NET: Registered PF_INET protocol family
[ 0.448977] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.457077] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.465399] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.473071] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.480688] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.487690] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.494115] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.500606] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.507884] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.513510] PCI: CLS 0 bytes, default 32
[ 0.520164] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.532028] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.537905] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.549322] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.560696] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.566597] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.572571] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.578606] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.585267] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.594044] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.602155] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.967567] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 0.972379] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.977236] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 0.984411] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 0.990699] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.996105] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.002957] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.009134] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.015057] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.021296] pci 0000:00:00.0: reg 0x14: [mem 0x60500000-0x6050ffff]
[ 1.027590] pci 0000:00:00.0: supports D1
[ 1.031510] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.038139] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x0d8000
[ 1.044107] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x01ffffff]
[ 1.050351] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.056589] pci 0000:00:01.0: supports D1
[ 1.060533] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.068071] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.076246] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.082225] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.088581] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.095946] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.101145] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.107143] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.113907] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.121081] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.127935] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
[ 1.133885] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.141074] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.148246] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.155484] pci 0000:02:00.0: supports D1 D2
[ 1.159681] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.166258] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.182354] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.187568] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.193584] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.200344] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.207485] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.214136] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.220681] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.227603] pci 0000:00:01.0: BAR 0: assigned [mem 0x60000000-0x61ffffff]
[ 1.234309] pci 0000:00:00.0: BAR 8: assigned [mem 0x62000000-0x620fffff]
[ 1.241076] pci 0000:00:00.0: BAR 9: assigned [mem 0x62100000-0x621fffff pref]
[ 1.248246] pci 0000:00:01.0: BAR 8: assigned [mem 0x62200000-0x622fffff]
[ 1.254954] pci 0000:00:01.0: BAR 9: assigned [mem 0x62300000-0x624fffff pref]
[ 1.262157] pci 0000:00:00.0: BAR 1: assigned [mem 0x62500000-0x6250ffff]
[ 1.268909] pci 0000:00:01.0: BAR 1: assigned [mem 0x62510000-0x6251ffff]
[ 1.275604] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.281683] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.287739] pci 0000:01:00.0: BAR 0: assigned [mem 0x62000000-0x620fffff]
[ 1.294442] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.299394] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.305412] pci 0000:00:00.0: bridge window [mem 0x62000000-0x620fffff]
[ 1.312180] pci 0000:00:00.0: bridge window [mem 0x62100000-0x621fffff pref]
[ 1.319362] pci 0000:02:00.0: BAR 0: assigned [mem 0x62300000-0x623fffff 64bit pref]
[ 1.327023] pci 0000:02:00.0: BAR 2: assigned [mem 0x62400000-0x62403fff 64bit pref]
[ 1.334756] pci 0000:02:00.0: BAR 4: assigned [mem 0x62404000-0x62404fff 64bit pref]
[ 1.342439] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.347321] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.353399] pci 0000:00:01.0: bridge window [mem 0x62200000-0x622fffff]
[ 1.360138] pci 0000:00:01.0: bridge window [mem 0x62300000-0x624fffff pref]
[ 1.369697] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.380877] printk: console [ttyS0] disabled
[ 1.385175] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.394213] printk: console [ttyS0] enabled
[ 1.402488] printk: bootconsole [early0] disabled
[ 1.415796] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 1.422359] spi-nor spi0.0: found mx25l12805d, expected w25q128
[ 1.428399] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[ 1.433578] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.440000] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.447325] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.455139] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.462518] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.470081] Creating 4 MTD partitions on "spi0.0":
[ 1.474870] 0x000000000000-0x000000030000 : "Bootloader"
[ 1.481403] 0x000000030000-0x000000040000 : "Config"
[ 1.487333] 0x000000040000-0x000000050000 : "factory"
[ 1.493622] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 1.501364] 0x000000050000-0x000001000000 : "firmware"
[ 1.507777] 2 uimage-fw partitions found on MTD device firmware
[ 1.513711] Creating 2 MTD partitions on "firmware":
[ 1.518681] 0x000000000000-0x0000002ac57d : "kernel"
[ 1.523629] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 1.532945] 0x0000002ac57d-0x000000fb0000 : "rootfs"
[ 1.537985] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 1.548104] mtd: setting mtd5 (rootfs) as root device
[ 1.553320] 1 squashfs-split partitions found on MTD device rootfs
[ 1.559548] 0x000000680000-0x000000fb0000 : "rootfs_data"
[ 1.700549] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.712899] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 1.723367] i2c_dev: i2c /dev entries driver
[ 1.730749] NET: Registered PF_INET6 protocol family
[ 1.738139] Segment Routing with IPv6
[ 1.741879] In-situ OAM (IOAM) with IPv6
[ 1.745875] NET: Registered PF_PACKET protocol family
[ 1.751021] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.764429] 8021q: 802.1Q VLAN Support v1.8
[ 1.774527] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.798101] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.806430] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=23)
[ 1.818847] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.819799] mt7530-mdio mdio-bus:1f lan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=24)
[ 1.839479] DSA: tree 0 setup
[ 1.854440] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.865637] Freeing unused kernel image (initmem) memory: 1232K
[ 1.871644] This architecture does not have kernel memory protection.
[ 1.878101] Run /sbin/init as init process
[ 1.882180] with arguments:
[ 1.882185] /sbin/init
[ 1.882190] with environment:
[ 1.882195] HOME=/
[ 1.882200] TERM=linux
[ 2.621692] init: Console is alive
[ 2.625472] init: - watchdog -
[ 3.712947] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.779865] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.790966] init: - preinit -
[ 5.044447] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.176059] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.211289] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.467189] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 5.479874] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.487972] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode
[ 5.495736] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.788994] jffs2: notice: (398) jffs2_build_xattr_subsystem: complete building xattr subsystem, 13 of xdatum (0 unchecked, 4 orphan) and 14 of xref (4 dead, 0 orphan) found.
[ 7.807437] mount_root: switching to jffs2 overlay
[ 7.822466] overlayfs: upper fs does not support tmpfile.
[ 7.841076] urandom-seed: Seeding with /etc/urandom.seed
[ 7.979419] procd: - early -
[ 7.982540] procd: - watchdog -
[ 8.592861] procd: - watchdog -
[ 8.598166] procd: - ubus -
[ 8.699213] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.707642] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.722679] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.737288] procd: - init -
[ 9.415168] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.659281] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 9.666768] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 10.019151] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 10.024860] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 10.031122] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 10.552785] urngd: v1.0.2 started.
[ 11.061474] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 11.067072] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 11.094351] mt7603e 0000:01:00.0: firmware init done
[ 11.267241] random: crng init done
[ 11.270732] random: 26 urandom warning(s) missed due to ratelimiting
[ 11.278395] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.288822] pci 0000:00:01.0: enabling device (0000 -> 0003)
[ 11.294524] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[ 11.326613] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 11.326686] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag
[ 11.374801] PPP generic driver version 2.4.2
[ 11.380816] NET: Registered PF_PPPOX protocol family
[ 11.393599] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.361065] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 17.689141] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 17.710304] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 17.718614] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 17.727142] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.735897] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode
[ 17.744256] br-lan: port 1(lan) entered blocking state
[ 17.749487] br-lan: port 1(lan) entered disabled state
[ 17.756692] device lan entered promiscuous mode
[ 17.761452] device eth0 entered promiscuous mode
[ 20.190133] br-lan: port 2(phy0-ap0) entered blocking state
[ 20.195738] br-lan: port 2(phy0-ap0) entered disabled state
[ 20.201935] device phy0-ap0 entered promiscuous mode
[ 20.202318] mt7530-mdio mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control off
[ 20.214747] br-lan: port 1(lan) entered blocking state
[ 20.220017] br-lan: port 1(lan) entered forwarding state
[ 33.807592] mt7615e 0000:02:00.0: Message 00000010 (seq 1) timeout
[ 33.813804] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 33.819847] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 34.104632] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 54.287682] mt7615e 0000:02:00.0: Message 00000010 (seq 2) timeout
[ 54.293918] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 54.299993] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 54.585228] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 74.767064] mt7615e 0000:02:00.0: Message 00000010 (seq 3) timeout
[ 74.773287] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 74.779343] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 75.064656] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 95.246836] mt7615e 0000:02:00.0: Message 00000010 (seq 4) timeout
[ 95.253048] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 95.259093] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 95.544367] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 115.725969] mt7615e 0000:02:00.0: Message 00000010 (seq 5) timeout
[ 115.732244] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 115.738354] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 116.023704] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 136.204481] mt7615e 0000:02:00.0: Message 00000010 (seq 6) timeout
[ 136.210704] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 136.216739] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 136.502341] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 156.682600] mt7615e 0000:02:00.0: Message 00000010 (seq 7) timeout
[ 156.688813] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 156.694838] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 156.979748] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 177.180980] mt7615e 0000:02:00.0: Message 00000010 (seq 8) timeout
[ 177.187193] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 177.193214] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 177.479073] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 197.672148] mt7615e 0000:02:00.0: Message 00000010 (seq 9) timeout
[ 197.678360] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 197.688928] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 197.979600] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 218.146861] mt7615e 0000:02:00.0: Message 00000010 (seq 10) timeout
[ 218.153161] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 218.159183] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 218.444354] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 238.624336] mt7615e 0000:02:00.0: Message 00000010 (seq 11) timeout
[ 238.630634] mt7615e 0000:02:00.0: Failed to get patch semaphore
[ 238.636673] mt7615e 0000:02:00.0: failed to load mediatek/mt7663pr2h_rebb.bin
[ 238.751175] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
[ 238.758259] br-lan: port 2(phy0-ap0) entered blocking state
[ 238.763905] br-lan: port 2(phy0-ap0) entered forwarding state ```