2 Gbps WAN/LAN NAT Routing on ramips MT7621 devices

How long ago was your snapshot build compiled?

Please check https://openwrt.org/faq/cannot_satisfy_dependencies

The latest

Is this patch able to be backported to 22.03 for the next release candidate?

1 Like

No, new features are never backported to release branches. Only bug fixes are backported.

How to solve this issue? Do I need to build a new image with those packages included? Is there a builder tool like there is for the official images?

Hello arinc9,
Not familiar with OpenWrt procedures,
Will your patch be integrated in future snapshot/stable releases?

Yes, once the patches on PR is applied, it takes a few days to produce an official SNAPSHOT image which includes my patches. It will also be included in the next stable release, probably the next year.


Sorry, that went right over my head.
"PR"? How would users know that PR is applied?
Thanks again.

Pull request

It will be closed and merged. You can see the status on the below link.


Thanks d687r02j8g

I've not tried this but seems promising

Nice job.
I see on your list of devices, you included Zyxel NR7101, which is a 5G Router.
It uses Wwan/Lan connection, but on iperf, if i test lan speed, i cannot reach full speed as well.
Does this patch can affect the mobile connection as well, increasing the lan speed from zyxel to another Router?
Or, can it be done to also increase WWAN/LAN speed?

Sorry for late reply, it’s been a busy day. No, it won’t affect wireless connection speed.

Do you happen to know whether it would be possible at all on an mt7621_ubnt_edgerouter-x-sfp with SFP being on external phy (eth5)?

I may have read something that bandwidth got split in max 1Gpbs because of internal wiring, but am not sure.

I tested EdgeRouter X SFP back in time. Here's what I recorded after my tests.

Ubiquiti EdgeRouter X SFP: External phy is wired TX→TX to the rgmii2 pinouts which needs the rgmii2 pin group claimed with gpio function to work. Muxing an internal phy to gmac1 results in only being able to receive traffic when the rgmii2 pin group is claimed with rgmii2 function.

I've tested this on an mt7621 device that is not officially supported yet: Adding OpenWrt support for Arcadyan WE420223-99 (KPN Experia WiFi) - #11 by Harm . It has only two Ethernet ports. I found that when the ports are used as a switch, this patch negatively affects performance. The CPU gets to handle all the traffic. Though when I use it as a router (so NAT) between the ports, the hardware offloading kicks in and forwards traffic at near-wirespeed.

So before having lan0 and lan1 in br-lan made it a switch where the cpu does not have to process the traffic, after the patch this makes the CPU do the work of forwarding packets. Am I missing a config setting?

a small question:
can this be of interest because I only use the MT7621 routers as relays or WIFI access points with the lan ports connected directly to the WAN port?

The modem in the NR7101 is wired to the SoC internal xhci controller so it won't be directly affected by this. In theory it could take some advantage of the extra bandwidth between cpu and switch, but it's hard to see where you'd use that bandwidth given the single ethernet port...

Answered here Users needed to test 2 Gbps WAN/LAN NAT Routing on ramips MT7621 devices - #53 by arinc9

Tried it on Cudy-X6

Tested straight through cable connecting to hosts. Get close to 1Gbps in both directions.
Test with router inline. Similar to arinc9 test except iperf3 client and server are separate hosts.
With 22.03 rc5 see about 1Gbps total.

[ ID][Role] Interval           Transfer     Bitrate         Retr
[  5][TX-C]   0.00-5.00   sec  83.8 MBytes   141 Mbits/sec   46             sender
[  5][TX-C]   0.00-5.00   sec  82.5 MBytes   138 Mbits/sec                  receiver
[  7][RX-C]   0.00-5.00   sec   441 MBytes   740 Mbits/sec  219             sender
[  7][RX-C]   0.00-5.00   sec   438 MBytes   734 Mbits/sec                  receiver

With arinc9 sysupgrade see about the same

 - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval           Transfer     Bitrate         Retr
[  5][TX-C]   0.00-20.00  sec   443 MBytes   186 Mbits/sec  280             sender
[  5][TX-C]   0.00-20.01  sec   439 MBytes   184 Mbits/sec                  receiver
[  7][RX-C]   0.00-20.00  sec  1.48 GBytes   637 Mbits/sec   28             sender
[  7][RX-C]   0.00-20.01  sec  1.48 GBytes   635 Mbits/sec                  receiver

I uploaded sysupgrade and did not keep config.
All I did was change IP addresses on router.
Is there some other config required?
hardware offload? where is that?