Youhua WS1200, Standard 5GHz settings (country RS) in channel 36, 20 dBm, set two APs, not working, showing 1 disabled but none of them working also when disabling one. Does not assign a mac address to the one AP showing as disabled although enabled.
mt76 broken ?
Did you attempt to associate a client?
1 Like
yes of course, with 80 MHz bandwidth it never connected
just put channel 'auto' and 20 MHz -> 5 GHz works... strange
just put channel 'auto' and 40 MHz -> 5 GHz works... strange
reboot
still works (40 MHz)
changed to 80 MHz -> 5 GHz not working
here's the system log
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: AP-DISABLED
Thu Mar 5 21:53:31 2020 daemon.err hostapd: ACS: Possibly channel configuration is invalid, please report this along with your config file.
Thu Mar 5 21:53:31 2020 daemon.err hostapd: ACS: Failed to start
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: AP-DISABLED
Thu Mar 5 21:53:31 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan1 wasn't started
Thu Mar 5 21:53:31 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan1-1 wasn't started
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: nl80211: deinit ifname=wlan1 disabled_11b_rates=0
Thu Mar 5 21:53:31 2020 kern.info kernel: [ 390.713936] device wlan1 left promiscuous mode
Thu Mar 5 21:53:31 2020 kern.info kernel: [ 390.718611] br-lan: port 3(wlan1) entered disabled state
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: interface state DISABLED->DISABLED
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: interface state DISABLED->DISABLED
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1-1: AP-DISABLED
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1-1: CTRL-EVENT-TERMINATING
Thu Mar 5 21:53:31 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan1-1 wasn't started
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: AP-DISABLED
Thu Mar 5 21:53:31 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-TERMINATING
Thu Mar 5 21:53:31 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan1 wasn't started
Thu Mar 5 21:53:31 2020 daemon.notice netifd: radio1 (4497): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process 3877 path ()
Thu Mar 5 21:53:32 2020 kern.info kernel: [ 391.221397] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Thu Mar 5 21:53:32 2020 daemon.notice netifd: radio1 (4497): ip: SIOCGIFFLAGS: No such device
Thu Mar 5 21:53:32 2020 daemon.notice netifd: radio1 (4497): Interface 1 setup failed: IFUP_ERROR
Thu Mar 5 21:53:42 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Thu Mar 5 21:53:43 2020 kern.info kernel: [ 402.371872] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Thu Mar 5 21:53:43 2020 kern.info kernel: [ 402.381291] br-lan: port 3(wlan1) entered blocking state
Thu Mar 5 21:53:43 2020 kern.info kernel: [ 402.386715] br-lan: port 3(wlan1) entered disabled state
Thu Mar 5 21:53:43 2020 kern.info kernel: [ 402.392446] device wlan1 entered promiscuous mode
Thu Mar 5 21:53:43 2020 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Mar 5 21:53:43 2020 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Thu Mar 5 21:53:43 2020 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ACS
Thu Mar 5 21:53:43 2020 daemon.notice hostapd: wlan1: ACS-STARTED
Is there a openwrt version which works for Youhua 1200 with 5 GHz ?
Seems other routers with the chipset have the same issue with openwrt https://github.com/openwrt/mt76/issues/199
19.07.0 brought 5 Ghz back on my YouHua 1200js. Had to reset to factory settings and enter all configuration again manually.
After that I could flash 18.06.8 with "keep settings" and keep 5 Ghz too.
Guess in theory it is better to run on new 18.06.8 than on old 19.07.0.
1 Like
Thanks a lot for sharing your solution !
Yeah, good advice, I‘ll go then for 18.06.8.
Have a great day and stay healthy !
cheers Blinton
Mine is broken too. I have downgraded to multiple builds and it's gone.
Not even a flicker of the LED.
My router is a TEW-692GR Trendnet.
Since upgrading my router can only stay connected for 6-8 mins before dropping and then I can't even find the network unless I pull the plug and reboot.
If i could I'd reflash to the original firmware.
I'm sad, lol.
Factory settings, as in an non Openwrt firmware?
Because that's my aim too but my router can't seem to TFTP
No, I just flashed new firmware, but without the checkmark to keep settings.
1 Like
Edited:
Thanks for the reply
Now I have upgraded to a resent snapshot. Flashed and kept settings from 18.06.8.
5 Ghz survived.
This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.