Hi, I have Belkin F5D7633 which is based on 6348 and board id 96348GW-10. Block size is 128k. With modified imagetag I have successfully installed latest trunk of OpenWRT. This router has BCM5325EKCM switch. I tried to configure vlans on it with robocfg, but it tells "No suitable module found for eth0 (managed by bcm63xx_enet)". May be this is limitation of bcm63xx ethernet driver or i should config it with swconfig?
Also somfing wrong with jffs:
bcm963xx: block unlock error: (status timeout)
Full dmesg:
Linux version 2.6.27.8 (alex@tux) (gcc version 4.1.2) #8 Wed Dec 17 21:37:03 EET 2008
Detected Broadcom 0x6348 CPU revision a2
CPU frequency is 256000000 MHz
16MB of RAM installed
board_bcm963xx: CFE version: 1.0.37-8.7
console [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348GW-10
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 80231a30, node_mem_map 80275000
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13724k/16384k available (1868k kernel code, 2660k reserved, 316k data, 120k init, 0k highmem)
Calibrating delay loop... 255.48 BogoMIPS (lpj=510976)
Mount-cache hash table entries: 512
net_namespace: 592 bytes
NET: Registered protocol family 16
registering 37 GPIOs
registering PCI controller with io_map_base unset
PCI: 0000:00:01.0 reg 10 32bit mmio: [0, 1fff]
bus: 00 index 0 io port: [8000000, 800ffff]
bus: 00 index 1 mmio: [30000000, 37ffffff]
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.276:1): initialized
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler cfq registered (default)
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=32
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW-10.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length bb8cd
bcm963xx_flash: Partition 2 is rootfs offset e0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3e0000 and length 20000
Creating 4 MTD partitions on "bcm963xx":
0x00000000-0x00020000 : "CFE"
0x00020100-0x000db9cd : "kernel"
mtd: partition "kernel" doesn't start on an erase block boundary -- force read-only
0x000e0000-0x003e0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=300000, len=E0000
0x00300000-0x003e0000 : "rootfs_data"
0x003e0000-0x00400000 : "nvram"
TCP bic registered
NET: Registered protocol family 17
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
bcm963xx: block unlock error: (status timeout)
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
eth1: link forced UP - 100/full - flow control off/off
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth1 entered promiscuous mode
br-lan: topology change detected, propagating
br-lan: port 1(eth1) entering forwarding state
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
br-lan: port 1(eth1) entering disabled state
br-lan: topology change detected, propagating
br-lan: port 1(eth1) entering forwarding state
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
b43-phy0: Broadcom 4306 WLAN found
phy0: Selected rate control algorithm 'minstrel'
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IPP2P v0.8.1_rc1 loading
ipt_time loading
firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
b43-phy0: Radio turned on by software
device wlan0 entered promiscuous mode
wlan0: deauthenticating by local choice (reason=3)
br-lan: port 2(wlan0) entering disabled state
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
br-lan: topology change detected, propagating
br-lan: port 2(wlan0) entering forwarding state