OpenWrt Forum Archive

Topic: Kamikaze 8.09 RC1 on the WRT54GLv1.1 WiFi Problem

The content of this topic has been archived on 6 Feb 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
Sartsj
29 Nov 2008, 14:41

Yesterday I flashed my WRT54GL with DD-WRT to the latest kamikaze 8.09 RC1 just to check out what I could do with it. Everything went fine, except for the fact that the Wifi doesn't seem to work. I'm probably doing something wrong, as I'm new to OpenWRT (I have quite a bit of experience with Linux itself and DD-WRT, but almost none with Linux on these router devices or wifi devices on linux in general).

Anyway I read the supported page for the WRT54GLv1.1 on the Wiki, and it does say it's supported on 8.09RC1 with 2.6 kernel, but after read a lot of topics on this forum, I'm not sure if this information is right. So am I doing something wrong or is it just not supported yet?

The b43 driver does find the wlan, although I'm not sure what to make of the second to last line..
By the way, if I run 'iwlist wlan0 scan', it does find another network in the neighbourhood, so it does seem to be working, but the 2 laptops I have just can't find the openwrt's network.

b43-phy0: Broadcom 5352 WLAN found
b43-phy0 debug: Found PHY: Analog 2, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
b43-phy0 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config

b43-phy0 debug: Chip initialized
b43-phy0 debug: 32-bit DMA initialized
Registered led device: b43-phy0::radio
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode

Also, here's the contents of /etc/config/wireless

config 'wifi-device' 'wlan0'
        option 'type' 'mac80211'
        option 'channel' '11'
        option 'disabled' '0'

config 'wifi-iface'
        option 'device' 'wlan0'
        option 'network' 'lan'
        option 'mode' 'ap'
        option 'ssid' 'sartsj.nl'
        option 'encryption' 'none'
        option 'hidden' '0'
Post #2
seezer
29 Nov 2008, 14:53

Do you have "hostapd" installed?

Post #3
Sartsj
29 Nov 2008, 15:40

I didn't have it installed at the time I wrote my post no, I figured I only needed that to use WPA, and even though I do want to use wpa, i wanted to get the wlan working first. But I installed it now (while having some major opkg and space issues tongue), and it works! Thanks for your help smile

P.S. Maybe the comment on the web interface Wifi page is a bit misleading? How about a rephrase to tell people you actually need hostapd to run in AP mode (even if you dont use wpa)?

(Last edited by Sartsj on 29 Nov 2008, 15:42)

Post #4
The Colour Of Heartache
29 Nov 2008, 16:07

I have hostapd-mini installed and no wifi, do I need to replace it with hostapd?

[edit]I'd just forgotten to set the channel. Silly me smile

Post #5
spiqsd
29 Nov 2008, 16:48

Hi,

I'm new to OpenWRT but I was willing to give it a try (I like more 2.6 than 2.4…).
I've compiled my own kamikaze version with all I need (KAMIKAZE 8.09, r13426) and flashed it on my WRT54GLv1.1.
It's almost working but I've encountered a few issues :
- My wifi is unstable: if a try to transfer a big file via ftp or download something with bit torrent, my wrt freezes
- My wireless clients cannot ping my wired clients: I get an ICMP port unreacheable from the wrt sad (same thing from a wired client to a wireless one)
I solved the 2nd issues with "iptables -A forwarding_lan -o br-lan -j ACCEPT" but I cannot solve the first one sad

Does someone have the same problem? Is there any solution?

Thanks

(my dmesg is filled with
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 ERROR: PHY transmission error
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 ERROR: PHY transmission error
b43-phy0 ERROR: PHY transmission error
b43-phy0 ERROR: PHY transmission error)

Post #6
spiqsd
29 Nov 2008, 23:23

After more research, my router doesn't freeze, il's 'just' the wifi who stop working after a while. (it's work longer if I don't download too much).
I don't know where to get debug message, I just have dmesg output, I hope someone can help me with that

b43-phy0 ERROR: PHY transmission error
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
printk: 1 messages suppressed.
b43-phy0 ERROR: PHY transmission error
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Updated beacon template at 0x468
b43-phy0 debug: Disabling hardware based encryption for keyidx: 0, mac: 00:1e:0b:8c:40:48
b43-phy0 debug: Disabling hardware based encryption for keyidx: 0, mac: 00:19:d2:8e:1d:69
b43-phy0 debug: Disabling hardware based encryption for keyidx: 0, mac: 00:1f:3c:1e:53:78
b43-phy0 debug: Updated beacon template at 0x68
b43-phy0 debug: Set beacon interval to 100
b43-phy0 debug: Updated beacon template at 0x468

Post #7
ghost_o
30 Nov 2008, 02:28

I have the exact problem with a wrt54gs v2.2  Setup for WPA2 Personal...  Loses connectivity with linux 2.6.27 kernels, iPhone, Windows XPO and Vista...  Reverting to the linksys firmware fixes issues....

Any ideas

Post #8
spiqsd
30 Nov 2008, 11:40

I just tried with the "trrunk" (r13439) and I still have the same problem sad

I've tried to run hostapd -d and I get this

1228001403.516795: WPA: Send EAPOL(version=2 secure=1 mic=1 ack=1 install=0 pairwise=0 kde_len=24 keyidx=2 encr=1)
1228001403.524550: Plaintext EAPOL-Key Key Data - hexdump(len=32): [REMOVED]
1228001403.527267: WPA: 00:1e:0b:8c:40:48 WPA_PTK_GROUP entering state KEYERROR
1228001403.527569: WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
1228001403.529188: WPA: 00:1e:0b:8c:40:48 WPA_PTK entering state DISCONNECT
1228001403.529469: hostapd_wpa_auth_disconnect: WPA authenticator requests disconnect: STA 00:1e:0b:8c:40:48 reason 2
1228001403.529838: WPA: 00:1e:0b:8c:40:48 WPA_PTK_GROUP entering state IDLE
1228001403.530065: WPA: 00:1e:0b:8c:40:48 WPA_PTK entering state DISCONNECTED
1228001403.530261: WPA: 00:1e:0b:8c:40:48 WPA_PTK entering state INITIALIZE
1228001403.532180: wlan0: STA 00:1e:0b:8c:40:48 IEEE 802.1X: unauthorizing port
1228001403.532635: wlan0: STA 00:1f:3c:1e:53:78 IEEE 802.11: deauthenticated due to local deauth request
1228001403.561746: wlan0: STA 00:19:d2:8e:1d:69 IEEE 802.11: deauthenticated due to local deauth request
1228001403.594736: Failed to set CTS protect in kernel driver
1228001403.596739: Failed to set Short Slot Time option in kernel driver
1228001403.598860: Could not set preamble for kernel driver
1228001403.601283: wlan0: STA 00:1e:0b:8c:40:48 IEEE 802.11: deauthenticated due to local deauth request

Post #9
ghost_o
2 Dec 2008, 03:24

I just went to the DD-WRT VINT build and the problem went away, but strangely - the kernels are the same as whiterussin that I tried!!!!!  I would much rather use openwrt since I can pick and choose packages, but no help is or pointers on how I can help is keeping m from going back..

I guess the 2,2 version is too old to warrant interest?

-Greg

Post #10
woody
19 Dec 2008, 15:03

I've had the same problem - even when I tried newer firmware (478.104 from Linksys WRT610N GPL sources, this was reported to help some people) I was getting PHY transmission errors.
Fortunately, the verison of b43 in Kamikaze 8.09 RC1 supports older firmware too (351.126 from package 4.80.53.0), I've tried this and now it works like a charm.

By the way, if you just want it to be easy, you could install Kamikaze 7.09 or 8.09 RC1 with kernel 2.4 smile

Post #11
graffen
1 Jan 2009, 17:26
woody wrote:

I've had the same problem - even when I tried newer firmware (478.104 from Linksys WRT610N GPL sources, this was reported to help some people) I was getting PHY transmission errors.
Fortunately, the verison of b43 in Kamikaze 8.09 RC1 supports older firmware too (351.126 from package 4.80.53.0), I've tried this and now it works like a charm.

By the way, if you just want it to be easy, you could install Kamikaze 7.09 or 8.09 RC1 with kernel 2.4 smile

How exactly do I go about installing the older firmware?

Post #12
chetan
1 Jan 2009, 23:30
graffen wrote:

How exactly do I go about installing the older firmware?

Here's what i did. It works for me.

apt-get install b43-fwcutter

wget http://downloads.openwrt.org/sources/broadcom-wl-4.80.53.0.tar.bz2
tar -jxf broadcom-wl-4.80.53.0.tar.bz2
cd broadcom-wl-4.80.53.0/kmod
mkdir ~/firmware
b43-fwcutter -w ~/firmware wl_apsta_mimo.o

cd ~/firmware
scp -r b43 root@192.168.1.1:~

# ssh to the router
ssh root@192.168.1.1
cd /
mv /lib/firmware/b43 /root/b43-old
mv /root/b43 /lib/firmware/

reboot

dmesg | grep "firmware version"
b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)

I'm not sure about some of the commands  above(especially whether the version that b43-fwcutter is extracting is FW11 or FW13), but it works for me.
let me know if changing the firmware fixes the frequent disconnects problem for you.

Post #13
graffen
2 Jan 2009, 01:39

Thanks, I managed to figure it out earlier on.
Unfortunately it hasn't helped much. My wireless still drops its connection but now without writing anything in the log. My router is a WRT54GL v 1.1 if that's any help.

Anything else I can try?

Post #14
NetworkPro
3 Dec 2011, 11:54

Hmmm

root@OpenWrt:/# logread
Dec  2 09:26:24 OpenWrt user.info sysinit: Sending discover...
Dec  2 09:26:25 OpenWrt user.info sysinit: Sending select for 10.0.0.6...
Dec  2 09:26:25 OpenWrt user.info sysinit: Lease of 10.0.0.6 obtained, lease time 1800
Dec  2 09:26:25 OpenWrt user.info sysinit: udhcpc: ifconfig wlan0 10.0.0.6 netmask 255.255.255.0 broadcast +
Dec  2 09:26:26 OpenWrt user.info sysinit: udhcpc: setting default routers: 10.0.0.1
Dec  2 09:26:26 OpenWrt user.info sysinit: udhcpc: setting dns servers: 10.0.0.1
Dec  2 09:26:27 OpenWrt user.notice ifup: Allowing Router Advertisements on wan (wlan0)
Dec  2 09:31:31 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 09:31:32 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:31:32 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 09:31:32 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:31:32 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 09:31:32 OpenWrt user.debug kernel: wlan0: associated
Dec  2 09:36:34 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 09:36:36 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:36:36 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 09:36:36 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:36:36 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 09:36:36 OpenWrt user.debug kernel: wlan0: associated
Dec  2 09:49:56 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 09:49:57 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:49:57 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 09:49:57 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:49:57 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 09:49:57 OpenWrt user.debug kernel: wlan0: associated
Dec  2 09:54:59 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 09:55:01 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:55:01 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 09:55:01 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 09:55:01 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 09:55:01 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:01:34 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:01:36 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:01:36 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:01:36 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:01:36 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:01:36 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:06:38 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:06:39 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:06:39 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:06:39 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:06:39 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:06:39 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:16:38 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:16:40 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:16:40 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:16:40 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:16:40 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:16:40 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:21:41 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:21:43 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:21:43 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:21:43 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:21:43 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:21:43 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:31:41 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:31:43 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:31:43 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:31:43 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:31:43 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:31:43 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:36:44 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:36:46 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:36:46 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:36:46 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:36:46 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:36:46 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:46:45 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:46:47 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:46:47 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:46:47 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:46:47 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:46:47 OpenWrt user.debug kernel: wlan0: associated
Dec  2 10:59:55 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 10:59:57 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:59:57 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 10:59:57 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 10:59:57 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 10:59:57 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:04:59 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:05:00 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:05:00 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:05:00 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:05:00 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:05:00 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:14:54 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:14:56 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:14:56 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:14:56 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:14:56 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:14:56 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:19:58 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:19:59 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:19:59 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:19:59 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:19:59 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:19:59 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:29:57 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:29:59 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:29:59 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:29:59 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:29:59 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:29:59 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:35:01 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:35:02 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:35:02 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:35:02 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:35:02 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:35:02 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:45:00 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:45:02 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:45:02 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:45:02 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:45:02 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:45:02 OpenWrt user.debug kernel: wlan0: associated
Dec  2 11:50:03 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 11:50:05 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:50:05 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 11:50:05 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 11:50:05 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 11:50:05 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:00:03 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:00:05 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:00:05 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:00:05 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:00:05 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:00:05 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:05:06 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:05:08 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:05:08 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:05:08 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:05:08 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:05:08 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:15:07 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:15:09 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:15:09 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:15:09 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:15:09 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:15:09 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:20:10 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:20:12 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:20:12 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:20:12 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:20:12 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:20:12 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:30:10 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:30:12 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:30:12 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:30:12 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:30:12 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:30:12 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:35:13 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:35:15 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:35:15 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:35:15 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:35:15 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:35:15 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:45:13 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:45:15 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:45:15 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:45:15 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:45:15 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:45:15 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:50:16 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 12:50:18 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:50:18 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 12:50:18 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 12:50:18 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 12:50:18 OpenWrt user.debug kernel: wlan0: associated
Dec  2 12:55:21 OpenWrt authpriv.info dropbear[2680]: Child connection from 10.0.0.5:49004
Dec  2 12:55:29 OpenWrt authpriv.notice dropbear[2680]: Password auth succeeded for 'root' from 10.0.0.5:49004
Dec  2 13:00:33 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 13:00:35 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 13:00:35 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 13:00:35 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 13:00:35 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 13:00:35 OpenWrt user.debug kernel: wlan0: associated
Dec  2 13:05:36 OpenWrt user.debug kernel: wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
Dec  2 13:05:38 OpenWrt user.debug kernel: wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
Dec  2 13:05:38 OpenWrt user.debug kernel: wlan0: authenticated
Dec  2 13:05:38 OpenWrt user.debug kernel: wlan0: associate with 00:23:08:xx:xx:xx (try 1)
Dec  2 13:05:38 OpenWrt user.debug kernel: wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
Dec  2 13:05:38 OpenWrt user.debug kernel: wlan0: associated
root@OpenWrt:/# dmesg
Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #11 Sun Oct 30 19:48:44 CET 2011
CPU revision is: 00029008 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0E, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Host (cc 0x817, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: chipcommon status is 0x0
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I 
ssb: core 0x0817, irq : 2(S)  3  4  5  6* D  I 
ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I 
ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802a09f0, node_mem_map 802e7000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13252k/16384k available (2332k kernel code, 3132k reserved, 355k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 199.16 BogoMIPS (lpj=398336)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  ?© 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
 CFI mfr 0x000000ec
 CFI id  0x000022a2
 Amd/Fujitsu Extended Query Table at 0x0040
  Newer Samsung flash detected, should be compatibile with Amd/Fujitsu.
  Fixed Samsung's Amd/Fujitsu Extended Query version from 3.3 to 1.3.
  Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000003f0000 : "linux"
0x00000011b000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000 
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:18:39:xx:xx:77
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'Linksys WRT54G/GS/GL'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Compat-wireless backport release: compat-wireless-2011-08-25
Backport based on wireless-testing.git master-2011-09-14
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
b43-phy0: Broadcom 5352 WLAN found (core revision 9)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
Broadcom 43xx-legacy driver loaded [ Features: PLID ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (209 buckets, 836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
b43-phy0: Loading firmware version 508.1084 (2009-01-14 01:32:01)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX AssocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated
wlan0: deauthenticated from 00:23:08:xx:xx:xx (Reason: 3)
wlan0: authenticate with 00:23:08:xx:xx:xx (try 1)
wlan0: authenticated
wlan0: associate with 00:23:08:xx:xx:xx (try 1)
wlan0: RX ReassocResp from 00:23:08:xx:xx:xx (capab=0x411 status=0 aid=1)
wlan0: associated

So what's happening here?

OpenWRT Image is /backfire/10.03.1-rc6/

P.S. Could be due to inactivity, as with constant ping on - it has not disconnected for 30 minutes now.

(Last edited by NetworkPro on 3 Dec 2011, 12:51)

The discussion might have continued from here.